CISCO SEMESTER 2: MODULE 12

1	Which of the following could describe the devices labeled "?" in the graphic? (Choose three.) DCE CSU/DSU LAN switch modem hub
2	Router A and Router B have been correctly configured to use RIP as a dynamic routing protocol and all intefaces on Router A and Router B are reporting "interface is up, line protocol is up" status. RIP is then configured on Router C using the following commands: RouterC(config)# router rip RouterC(config-router)# network 192.168.4.0 RouterC(config-router)# network 172.16.0.0 If no additional routing is configured on Router A, Router B, and Router C, what will be the result? Networks 192.168.12.0/24, 192.168.4.0/24, and 172.16.0.0/16 will be unreachable from Router A. Router A will have no knowledge of network 192.168.12.0/24, but will have routes to networks 192.168.4.0/24 and 172.16.0.0/16. All networks shown in the graphic will be reachable by Router A, Router B, and Router C. Networks 192.168.4.0/24 and 172.16.0.0/16 will be unreachable from Router A and Router B.

3	The following access list has been correctly applied to a router interface: access-list 52 deny 172.30.65.52 access-list 52 permit any Which of the following statements are true about this ACL? (Choose three.) This is an invalid ACL because the wildcard mask is missing from the command. A wildcard mask of 0.0.0.0 is assumed for 172.30.65.52. This is an extended IP access list. All traffic from 172.30.65.51 will be permitted. This is a standard IP access list.
4	Refer to the graphic. Assuming default metrics are used and the network is fully converged, which path will the IGRP routing protocol use to send a packet from Router A to Router F? A, D, E, F A, B, D, E, F A, C, D, E, G, F A, B, D, E, G, F

5	Neither router in the graphic has a host table or DNS available. The interfaces and passwords have been correctly configured. Which of the following commands will initiate a Telnet session? (Choose two.) ATL> connect CHI ATL> telnet CHI ATL# 192.168.4.2 ATL# connect ATL CHI# telnet 192.168.4.1 CHI# telnet ATL
6	What will occur if the command service password-encryption is entered on a router? (Choose two). It will allow only the user EXEC mode password to be encrypted. It will set an MD5 hashing algorithm on all unencrypted passwords. It will apply a weak encryption to all unencrypted passwords. It will set the enable secret password to be encrypted. It will apply an MD5 hashing algorithm to encrypt the console and telnet passwords. It will configure the user EXEC mode, telnet, and enable passwords as encrypted.

7	A network administrator must configure a serial interface with an IP address. The configuration must also identify the remote site to which the interface is connected. Which set of commands will meet these requirements? Chicago(config)# description San Jose T1 Chicago(config)# interface serial0/0 Chicago(config-if)# ip address 192.168.204.9 255.255.255.252 Chicago(config)# interface serial0/0 Chicago(config-if)# ip address 192.168.204.9 255.255.255.252 Chicago(config-if)# description San Jose T1 Chicago(config)# interface serial0/0 Chicago(config-if)# ip address 192.168.204.9 netmask 255.255.255.252 Chicago(config-if)# description San Jose T1 Chicago(config)# interface serial0/0 Chicago(config-if)# ip address 192.168.204.9 255.255.255.252 Chicago(config-if)# remote site San Jose T1 Chicago(config)# interface serial0/0 Chicago(config-if)# ip address 192.168.204.9 255.255.255.252 Chicago(config-if)# interface description San Jose T1
8	A network administrator has enabled RIP on routers B and C in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A? A(config)# router rip A(config-router)# passive-interface S0/0 B(config)# router rip B(config-router)# network 192.168.25.48 B(config-router)# network 192.168.25.64 A(config)# router rip A(config-router)# no network 192.168.25.32 B(config)# router rip B(config-router)# passive-interface S0/0 A(config)# no router rip

9	Which of the following describe Telnet on a router? (Choose two.) Simultaneous incoming Telnet sessions can be hosted by a router. Telnet is the most basic testing mechanism available. A Telnet session can only be initiated in privileged EXEC mode. Five separate Telnet lines are specified by the configuration line vty 0 4. Telnet is classified as a network layer protocol.
10	Which commands will show the status and IP address of all interfaces on a router? (Choose two.) show protocols show ip protocols show version show interfaces show ip ports

11	Which router command will generate the router output shown in the graphic? show arp show protocols show interface FastEthernet0/0 show interfaces show hardware
12	Which of the following are valid boot system commands? (Choose two.) Router(config)# boot system ram Router(config)# boot system rom Router(config)# boot system IOS flash Router(config)# boot system flash c2600-d-mz.121-3 192.168.10.5 Router(config)# boot system tftp c1700-l-mz.131-2 172.16.24.7

13	During initial router bootup the following line appears: "NVRAM invalid, possibly due to write erase." What are two possible reasons for this result? (Choose two.) The startup-config file was not saved to RAM before reboot. The IOS has been erased. The router has not been configured. The startup-config file cannot be located. The router will not enter initial configuration dialog.
14	While planning an IOS upgrade, the administrator issues the show version command. Based on the output in the graphic, what is the current IOS boot location? RAM NVRAM Flash ROM

15	Which statements are true regarding setup mode? (Choose three.) Press Ctrl-z to terminate setup mode. Enter a question mark (?) for help at any point. Press Spacebar to accept the default settings. Use setup mode to enter complex protocol features. Press Enter to accept the default settings. Press Ctrl-c to abort configuration dialog.

16	Which router components and operations are correctly described? (Choose two.) ROM - stores the backup configuration file RAM - loads the operating system NVRAM - stores the configuration file Flash - executes diagnostics at bootup POST - runs diagnostics on hardware modules DRAM - loads the bootstrap
17	access-list 199 deny tcp 178.15.0.0 0.0.255.255 any eq 23 access-list 199 permit ip any any Assuming this ACL is correctly applied to a router interface, which statements describe traffic on the network? (Choose two.) All FTP traffic from network 178.15.0.0 will be permitted. All Telnet traffic destined for network 178.15.0.0 will be denied. Telnet and FTP will be permitted from all hosts on network 178.15.0.0 to any destination. Telnet will not be permitted from any hosts on network 178.15.0.0 to any destination. Telnet will not be permitted to any host on network 178.15.0.0 from any destination.

18

Refer to the graphic. Communication is needed between the LAN connected to the fa0/0 interface of the Kansas router and the fa0/0 interface of the Maine router. All hosts on those LANs also need connectivity to the Internet. Which commands will allow this communication? (Choose three).

Kansas(config)# ip route 192.168.6.0 255.255.255.0 172.18.64.2

Kansas(config)# ip route 192.168.6.0 255.255.255.0 s0/1

Kansas(config)# ip route 0.0.0.0 0.0.0.0 s0/1

Maine(config)# ip route 192.168.6.0 255.255.255.0 172.18.64.1

Maine(config)# ip route 0.0.0.0 0.0.0.0 s0/1

Maine(config)# ip route 172.16.32.0 255.255.255.0 172.18.64.2

19

Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.) Router(config)# line vty 0 3 Router(config-line)# password c13c0 Router(config-line)# login
	The entries specify three Telnet lines for remote access.
	The entries specify four Telnet lines for remote access.
	The entries set the console and Telnet password to "c13c0".
	Telnet access will be denied because the Telnet configuration is incomplete.
	Access will be permitted for Telnet using "c13c0" as the password.

20	What are some reasons to change the configuration register setting? (Choose two.) to force the system to ignore the configuration file stored in NVRAM to monitor password changes to change the POST sequence to force the router to boot the IOS from NVRAM to force the system into ROM monitor mode
21	A network administrator issues the erase startup-config command on a configured router with the configuration register set to 0x2102 and observes the following output: Erasing the nvram filesystem will remove all files! Continue? [Confirm] [OK] Erase of nvram: complete If the router unexpectedly loses power after this sequence, what will occur when power is restored? The router will enter ROM monitor mode upon completion of the power-on self test (POST). The router will load the last known valid configuration file. The router will enter Rx-boot mode. The router will prompt the user to enter setup mode or to continue without entering setup mode.

22	Which of the following are true regarding the use of login banners? (Choose two.) The message is only displayed in privileged EXEC mode. The message can be seen by everyone who accesses the router. "Good morning" is an appropriate message to display. The banners should display warning messages. The banners should identify circuits and other devices connected to the router.
23	Which router component stores the information that is displayed by the show ip route command? CPU Flash NVRAM RAM

24	What information can be learned during the initial router bootup? (Choose two.) the configuration register value the number and types of interfaces installed the router model and the amount of memory that is available the amount of memory required to load the IOS and configuration the number of interfaces with connected cables
25	Which of the following describes CDP? (Choose three.) provides information on directly connected Cisco routers that have CDP enabled can only be configured between Cisco devices used for debugging Layer 4 connectivity issues should be disabled on non-locally managed ports presents a potential security risk

26	What can a network administrator do to recover from a lost router password? perform a reload or reset telnet from another router and issue the show running-config command to view the password boot the router to ROM monitor mode and configure the router to ignore NVRAM when it initializes boot the router to bootROM mode and enter the b command to load the IOS manually
27	A network administrator wishes to load a configuration file from a TFTP server into NVRAM on a router. Which of the following methods will create a startup-config file in NVRAM that matches the contents of the configuration file on the TFTP server? Copy the configuration file from a TFTP server using the command copy tftp startup-config. Copy the configuration file from a TFTP server using the command copy <>. Copy the file to RAM from a console connection using the copy tftp running-config command. Then reload the router to use the new configuration. Paste the configuration file to the command line of the router while in global configuration mode. Then issue the copy startup-config running-config command.

28	Which of the following are primary functions of a router? (Choose two.) packet switching microsegmentation domain name resolution path selection flow control
29	Which of the following are true regarding an interface description? (Choose three.) It is a message that is displayed at login. It does not affect the operation of the router. It contains the circuit identifiers of the interface by default. It could allow support personnel to better understand the scope of an interface problem. It could identify the purpose and location of the interface. It wastes bandwidth and slows down interface problem resolution.

30

Which ACL can be applied in the outbound direction of Serial 0/0 on router B in the graphic to allow all IP traffic from LAN A to the Internet, allow Web traffic from LAN B to the Internet, and deny all other traffic to the Internet? access-list 98 permit 192.168.2.0 0.0.0.255 any access-list 98 permit tcp 10.90.3.0 0.0.0.255 any eq www access-list 125 permit ip 192.168.2.0 0.0.0.255 any access-list 125 permit tcp 10.90.3.0 0.0.0.255 any eq www access-list 132 permit ip 192.168.2.0 0.0.0.255 any access-list 132 permit tcp 10.90.3.0 0.0.0.255 any eq www access-list 132 permit ip any any access-list 156 permit ip 192.168.2.0 0.0.0.255 any access-list 156 permit ip 10.90.3.0 0.0.0.255 any eq www

31	The following access list has been created to prevent traffic from host 172.23.40.36 from accessing the 192.168.34.0 network. access-list 44 deny host 172.23.40.36 access-list 44 permit any Refer to the graphic. Which group of commands will properly place the access list so that the host is denied access only to network 192.168.34.0? Rome(config)# interface fa0/0 Rome(config-if)# ip access-group 44 in Rome(config)# interface s0/1 Rome(config-if)# ip access-group 44 out Tokyo(config)# interface s0/0 Tokyo(config-if)# ip access-group 44 in Tokyo(config)# interface fa0/0 Tokyo(config-if)# ip access-group 44 out
32	Which of the following are true statements regarding IGRP and RIP? (Choose two.) IGRP uses a combination of different metrics for path selection. RIP is a proprietary protocol developed by Cisco. RIP has the ability to scale to large networks. IGRP has the ability to scale to large networks.

33	In what order will the initial startup routine of a router locate and load the IOS if the config-register setting is 0x2102 and there are no boot system commands present in the startup-config file? Flash, ROM, TFTP server RAM, Flash, NVRAM Flash, TFTP server, ROM ROM, TFTP server, Flash Flash, NVRAM, RAM ROM, Flash, TFTP server
34	What will occur when the following ACL is applied inbound to both FastEthernet interfaces of Router A in the graphic? access-list 125 permit tcp 192.168.2.0 0.0.0.255 10.90.3.0 0.0.0.255 eq 23 access-list 125 permit tcp 10.90.3.0 0.0.0.255 192.168.2.0 0.0.0.255 eq 23 access-list 125 permit tcp 192.168.2.0 0.0.0.255 any eq www Workstations A and B will be able to Telnet to each other. Workstation A will be allowed to access Web servers on the Internet, while Workstation B will be denied Internet Web access. Workstations A and B will be able to Telnet to each other. All other traffic will be denied. The ACL will have no effect because it should be applied in the outbound direction on the FastEthernet interfaces. The ACL will deny all traffic because of the implied deny ip any any statement at the end of the ACL.

35	Which of the following commands will correctly configure an extended ACL? (Choose two). Router(config)# access-list 18 permit tcp host 192.168.73.3 eq 25 Router(config)# access-list 102 permit tcp 10.43.0.0 0.0.255.255 any eq 80 Router(config)# access-list 187 permit tcp host 192.168.42.34 172.29.0.0 0.0.255.255 eq 23 Router(config)# access-list 99 permit host 10.217.32.3 Router(config)# access-list 128 permit tcp host 192.168.100.31 eq 23
36	Refer to the graphic. Which command will create a standard ACL that will apply to outbound traffic on interface Fa0/0 of router A and will deny IP traffic from any host on network 172.16.34.0/24 that is destined for network 192.168.5.0/24 while allowing all other IP traffic? access-list 2 deny 172.16.34.0 0.0.0.0 access-list 2 permit any access-list 33 deny 172.16.34.0 0.0.0.255 access-list 33 permit any access-list 42 deny 172.16.34.0 access-list 42 permit any access-list 56 deny tcp 172.16.34.0 access-list 56 permit ip any

37	Refer to the network and routing table entries shown in the graphic. How much time will elapse before Router A expects to receive another update from Router B? 5 seconds 13 seconds 17 seconds 25 seconds 65 seconds 90 seconds
38	Refer to the graphic. Which series of commands will create static routes that will allow Router A and Router B to deliver packets destined for LAN A and LAN B, and direct all other traffic to the Internet? RouterA(config)# ip route 10.90.3.0 255.255.255.0 192.168.3.2 RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 0.0.0.0 0.0.0.0 s0/0 RouterA(config)# ip route 10.90.3.0 255.255.255.0 192.168.3.2 RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2 RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2 RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 172.20.20.4 255.255.255.252 s0/0 RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2 RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 0.0.0.0 0.0.0.0 s0/0

39	Which of the following describe Ethernet and serial interfaces of a router? (Choose two.) They are enabled by default. They may be administratively disabled by using the shutdown command. They must be configured with an IP address and subnet mask in order to forward packets. They must be configured with an IP address and a clockrate in order to forward packets. They may be administratively disabled by using the no shutdown command.
40	Which of the following statements are true regarding routed protocols? (Choose two.) They provide enough information in the Layer 3 address to allow a packet to be forwarded from one network to another. They carry user data between networks. They allow routers to share information about networks and their proximity to each other. They are used by routers to maintain routing tables. RIP and IGRP are routed protocols.

41	If a PC does not have network connectivity to a router, which router port can be used to establish communication? console Ethernet serial VTY
42	Router A is directly connected to the networks shown in the graphic and has a default route that points to Router B. All interfaces are active and properly addressed. However, when the workstation on network 172.16.4.0/24 sends a packet to destination address 172.16.201.5, it is discarded by Router A. What can be a reason for this result? The ip classless command is not enabled on Router A. Router B is in a different autonomous system than Router A. Routers A and B are using different routing protocols. Router A has no route in its routing table that includes the address 172.16.201.5.

43	Which of the following prevent successful loading of the Cisco IOS from flash memory? (Choose two.) a configuration register set at 0x2102 a missing startup-configuration file a boot system command not present in the startup-config file an incorrect configuration register setting a boot field set to 2
44	Which two steps describe how to create a functional physical connection between a router console and a terminal? (Choose two.) Use a crossover cable to connect the terminal serial port to the router console port. Use a rollover cable to connect the terminal NIC to the router console port. Use an RJ-45 to DB-9 adapter on the terminal serial port to connect to the cable going to the router console. Use a transceiver to connect a straight-through cable to the router console port. Use a straight-through cable to connect the router console port to the terminal NIC. Use a rollover cable to connect from a terminal serial port to the router console port.

45

Refer to the graphic. A network administrator has a console connection to Router A. Pings to Router B are successful, but pings to Routers C and D fail. What is the first step in troubleshooting the problem? Use the show cdp neighbors detail command from router A to gather information about all Cisco routers in the network. Use the traceroute command to discover exactly which link in the network is down. Use an extended ping from router A to each router in the network. Use the show interfaces command from a Telnet session on router B to check the connection to router C.

46	Based on this partial output of the show ip route command, which routing protocol is configured on the router? I 172.16.3.0/24 [100/80135] via 172.16.2.2, 00:00:27, Serial0/0 RIP v1 RIP v2 IGRP EIGRP OSPF IGP
47	Assuming the following ACL is correctly applied to a router interface, what can be concluded about this set of commands? (Choose two.) Router(config)# access-list 165 deny tcp 192.28.115.0 0.0.0.255 172.20.0.0 0.0.255.255 eq 23 Router(config)# access-list 165 permit ip any any This is a standard IP access list that denies network 192.28.115.0 Telnet access to the 172.20.0.0 network. All Telnet traffic destined for 172.20.0.0 from any network will be denied access. Network 192.28.115.0 is denied Telnet access to the 172.20.0.0 network. Network 172.20.0.0 is denied Telnet access to the 192.28.115.0 network. All FTP and HTTP traffic destined for 172.20.0.0 will be permitted access.

48	What could a Cisco support technician learn from the IOS filename c2600-d-mz.121-3? (Choose three.) the format of the file the RAM memory requirements of the file the version number of the file the size of the file the device platform of the file
49	Which of the following are correct statements verified by the router output shown in the graphic? (Choose two.) Layer 3 connectivity exists between BigCity and the devices in the Device ID column. Layer 2 connectivity exists between BigCity and the devices in the Device ID column. All devices shown in the Device ID column use the TCP/IP protocol suite. All devices shown in the Device ID column can be pinged from BigCity. All devices listed in the Device ID column are directly connected to BigCity.

50

What are the results of setting the boot field bits in the configuration register to "0000"? (Choose two.) The startup-config file will be ignored at bootup. The router will load the IOS from Flash. The router will enter ROM monitor mode upon reload. The router will enter boot ROM mode and have limited capabilities. The administrator can enter the b command to manually boot the IOS.